axle sliders and hand guards

[kakoii]

for an 2008 sm610

pm me if you've got some hanging around in the shed..

cheers,

[Muzzard]

Extreme make a set of handguards that are around $60 with mounts from most bike shops.
The axle sliders most make from Delrin rod and all thread.

Theres several links here for custom made ones though too.

[huskyboy610]

I've got these Axle sliders on my 610, been through a few scrapes now. Just use spare rod from bunnings.

pretty cheap eventhough shipped from the UK


http://members.lycos.co.uk/mgmoto/html/crash_bobbins.html

[Wobbly]

http://www.vsmr.net/wiki/index.php/Axle_Sliders

[Slain]

i got the same ones as huskyboy, cost me $35 delivered.

[SMC690]

Damn, I got ripped, glad KTM have changed the way they make them now.

[Muzzard]

Damn, I got ripped, glad KTM have changed the way they make them now.
Looking at the nice hollow axles the other day on yours Justin,
I was thinking some Delrin machined to fit inside and a retainer like your bar ends to hold them in :P

[kakoii]

cheers for the help, Lads.

i'll be looking into these a bit more...

:)

as far at the hand guards go.

I'm assuming there's no major structural difference between acerbis and ego?

does one stand above the other for reputation?

[HyperGez]

I've got the ego's on my husky, either set will do the job mate.

[SM93]

i prefer the acerbis supermoto guards after owning both pairs but very little difference. if u like the look of one over the other get them

[Sonic]

hey i did speak to this guy via email on these sliders and he said if there were a few club members interested he would give us a discount to help the club out
but thats only if there was any interest in them ,i did order a set of him as well
i also did speak to him about buying a few sets to sell here ,he was interested as well but would have to have them sent sea as freight kills the price on em
if there was interest in them i would get 20 od sets sent and sell them to members cheapo and some for chimpos on egay
any interest ??

[kakoii]

Yep, I'm interested.

[SMC690]

Looking at the nice hollow axles the other day on yours Justin, I was thinking some Delrin machined to fit inside and a retainer like your bar ends to hold them in :P

Too late now, I bought the HardParts genuine ones, they offered me a deal I could not refuse. ;)

[Wobbly]

Are they the special ktm ones that snap off when your bike falls over? :lol2:

[SMC690]

Nah, they now make them out of Delrin, they must have read this forum. :)

[kakoii]

hey i did speak to this guy via email on these sliders and he said if there were a few club members interested he would give us a discount to help the club out
but thats only if there was any interest in them ,i did order a set of him as well
i also did speak to him about buying a few sets to sell here ,he was interested as well but would have to have them sent sea as freight kills the price on em
if there was interest in them i would get 20 od sets sent and sell them to members cheapo and some for chimpos on egay
any interest ??

Any word on these Sonic?

[kakoii]

fuck it.

Just bought some off the site.

:)

[kakoii]

they arrived today

need to find something to cut the rod with and i'll also have to trim back the right fork protector about 4mm so it will fit.

All in all they look like they'll do the job fine.

[HyperGez]

Now you just have to test them! :D
Ground down axle sliders give street cred! :roost:

[Sonic]

Now you just have to test them! :D
Ground down axle sliders give street cred! :roost:

sweet ill get my grinder out then should ad a few points :D

[Wobbly]

Straight grind marks = street cred

Circular grind marks does not :D